 |
Safety
Cover Installation Guide
Installing your own
safety cover can save you a lot of money and
with our installation guide, it couldn't be
easier! With our detailed diagrams and step-by-step
instructions you should have your safety cover
installed quickly and safely.
If you need help installing your safety cover,
give us a call and we will help you along!
|
|
|
| Click
on the titles below to view guide |
|
|
|
|
|
 |
Figure
1 |
|
| A:
ON-GROUND COVER INSTALLATION INSTRUCTIONS: |
| Please
Note: if you are installing a Loop-Loc On-Ground
swimming pool cover using Loop-Loc's patented Bracket,
please disregard this installation guide, and use
the Installation Instructions which are packaged with
your hardware. (This Installation Guide is only required
if your On-ground cover is being Wood Deck Anchor
Flanges) |
| B:
IN-GROUND COVER INSTALLATION INSTRUCTIONS: |
| Step
1:
Measure the cover and pool exactly. Lay cover over
pool and adjust for equal overlap at all 4 corners
of the pool. Example: a 20' x 40' rectangular pool
takes a 22' x 42' cover. Overlap may vary 11"
to 14". |
Step
2:
To determine anchor points for the 2 anchors at each
corner of the pool, measure 18" back from the
edge of the cover (not the edge of the pool). Measure
at right angles to the cover edge, as illustrated
in Figure 1. |
Step
3:
Install the 8 anchors at the 4 corners of the
pool (see Anchor Installation). Attach springs to
cover straps, then install springs on anchors, using
Installation Rod (see Spring Installation) |
Step
4:
Snap a chalk line along the perimeter of the pool,
using corner anchors 18" from a cover as a guide.
See Figure 1 above. This will ensure that all anchors
will be aligned. |
| Step
5:
With all 4 corners secured, locate remaining anchor
points individually by pulling back each strap until
cover edge is aligned with corner overlap. Anchors
should be installed 18" back from aligned cover
edge along strap line at right angle to cover edge.
(Note: Chalk line should indicate proper distance
for anchors to be aligned) |
Step
6:
When all anchors and springs are installed, conduct
a final check. Adjust all springs so that tension
is equal on all parts of the cover and the cover edge
lies in a straight line on all sides. |
|
|
Figure
2
Figure
3 |
Step
1:
Refer to Anchor Plan provided with cover. Cover
must be laid out according to the plan to ensure
proper installation. |
| Step
2:
Using stakes and rope, lay a rope grid across
the pool as shown in Figure 2. Rope must be
tight enough to support the cover while you
install it. |
Step
3:
Stretch cover across pool and adjust for equal
overlap on all sides. Overlap may vary 15"
to 18" depending on the cover size. |
Step
4:
Locate anchor positions on Anchor Plan for straps
numbered 1-4 (see Figure 3). Measure and mark
anchor positions on deck 18" from edge
of cover. |
Step
5:
Install anchors (see Anchor Installation) and
springs (see Spring Installation) for straps
numbered 1-4 in order shown on Figure 3. To
ensure proper fit, follow spring compression
guidelines. |
Step
6:
Locate and install anchors and springs for straps
numbered 5-8 in order shown on Figure 3. |
Step
7:
With first 8 anchors secured, locate and install
remaining anchors in an alternating pattern,
working from the middle of the cover to the
ends. Secure each spring as individual anchors
are installed. |
Step
8:
When all anchors and spring are installed, conduct
a final check. Adjust all springs so that tension
is equal on all parts of the cover and the cover
lies flat on the deck, with no bunches or creases. |
$9.95
SHIPPING ON ALL ORDERS $199.99 & LOWER. $19.95 SHIPPING ON ALL ORDERS $200.00 OR MORE!*
No Additional
Handling Charges** |
*
Additional shipping costs apply for certain zip codes.
Please call for information and pricing.
** Not applicable for some zip codes. We will contact you if your zip code
is affected. Additional charges apply for HI and AK Orders, as well as orders
from outside the Continental US. Please call for pricing.
|
|
|
